Auseal Solvent can also be used to clean concrete surfaces and prepare them for sealing.  It can also soak out grease and oil stains from concrete prior to sealing.

TYPICAL PROPERTIES     

Appearance:                          Clear colourless low – viscous liquid

Total Solids:                           N/A

pH:                                         N/A

Specific Gravity:                   0.8

Water Solubility:                    Immiscible

Min Film Forming Temp:    N/A

Min Film Thickness:              N/A

Application rate:                    See Below.

APPLICATION:                   

Auseal Solvent is used for thinning down solvent based resin products, either because of high viscosity, or to assist penetration into the substrate. Auseal Solvent is also used for cleaning spray equipment, broom heads or rollers.  If using to clean spraying machines just flush with solvent.

WARNINGS:

• DO NOT use on plastics or surfaces affected by solvents.
• DO NOT use on paint, lacquered, varnished or polished surfaces.
• DO NOT use on carpets, vinyls or similar floor surfaces.
• DO NOT use on any glazed products.
• Contains flammable solvents and precautions should be taken when using.

PACKAGING & SAFETY:

Auseal Solvent is available in 5, 10, 20 and 200 litre drums.

Refer to the Safety Data Sheet before handling or use.

Important Note:

The use of this product sold is beyond the control of the seller all conditions and warranties of all, kind in relation to its use or application or otherwise are hereby excluded save for those non – exclusive warranties implied by The Trade Practices Act, 1974 CtH) or any other act.  As this information is of as general nature we cannot assume responsibility for individual cases.  It is the users responsibility to determine whether the surface of the product is to be applied is thoroughly clean of any grease and oil as per instructions.

The post Xylene first appeared on Auseal Pty Ltd.

Colour: Auseal Cement Off White

The post WB Epoxy first appeared on Auseal Pty Ltd.

SAME DAY SEAL is based on 100% acrylic copolymer.

The post Same Day Seal first appeared on Auseal Pty Ltd.

POWERSEAL is one of the toughest Single Pack Two coat products in the market.

Auseal – is a hard surface Urethane based Concrete Sealer. It is a two coat system and is suitable for Factory Floors, Warehouses, Service Stations, Workshops and inside garages. Auseal Powerseal is not UV and therefore is only suitable for indoors. Protection against most chemicals, fats, oils, alkalis and salts.

The post Powerseal Urethane Colour Primer first appeared on Auseal Pty Ltd.

POWERSEAL is one of the toughest Single Pack Two coat products in the market.

Auseal – is a hard surface Urethane based Concrete Sealer. It is a two coat system and is suitable for Factory Floors, Warehouses, Service Stations, Workshops and inside garages. Auseal Powerseal is not UV and therefore is only suitable for indoors. Protection against most chemicals, fats, oils, alkalis and salts.

The post Powerseal Urethane Clear Primer first appeared on Auseal Pty Ltd.

The post Hi Gloss Seal first appeared on Auseal Pty Ltd.

AUSEAL – EC30 is a general purpose concrete sealant specifically formulated for sealing and protecting dry concrete based domestic floors and driveways where a medium gloss finish is required. AUSEAL EC30 is based on 100% acrylic copolymer.

The post EC 30 Sealer first appeared on Auseal Pty Ltd.

AUSEAL – EC30 is a general purpose concrete sealant specifically formulated for sealing and protecting dry concrete based domestic floors and driveways where a medium gloss finish is required. AUSEAL EC30 is based on 100% acrylic copolymer.

The post EC 30 Colour Sealer first appeared on Auseal Pty Ltd.

The post EC 25 Sealer first appeared on Auseal Pty Ltd.

The post EC 25 Colour Sealer first appeared on Auseal Pty Ltd.